ROKTOOLS
WG-218 is updated from ROK WG-208, These two bridge cam gauge almost the same except pointer. WG-218 has two pointers on both side. One can measure from both sides without changing its position. These gauges are all used in bridge and building construction, pipe installing, ship inspection or building.
- Measurements if possible in either inches or millimeters
- General Linear Measurements up to 50mm ( 2 inch)
- Angle of preparation (0°~60°)
- excess weld metal
- Depth of undercut
- Meet ANSI standard
- OEM welcomed
Features:
Specification:
Size(approx.):
Large size: mirror diameter 82mm. can be extended to 760mm
Medium: mirror diameter 55mm. can be extended to 940mm
Small: mirror diameter 32mm. can be extended to 910mm
With LED (battery is not included)
Introduction:
1. The mirror is equipped with LED lights, with light detection, and the 360-degree rotating lamp head is suitable for small space operation.
2. The rotary joint has no dead angle, the telescopic rod can be adjusted, and the length can be adjusted freely.
3. Rubber non-slip handle, non-slip design, comfortable to use.
4 The tool can detect engine oil leakage, see the water tank leaking, look at the internal structure of the headlights,
and see the oil on the evaporator surface.
5. Instructions for use: Open the cover, turn left to open the battery cover,
pull out the insulation sheet of the insulated battery, close the cover and open the switch
6. Alloy steel material, high quality, high-definition mirror, high-definition reflective objects. Use range mechanical repair, home and auto parts repair.
List:
inspection mirror *1(S. M, L)
- Standards: GB/T1764-79 GB/T134522-92 ISO2808-74
- Measuring Range: 25~2032µm (1~80mil)
- Values:
- 25, 51, 75, 102, 127, 152, 178, 203, 229, 254, 279, 305, 356, 406, 457, 508, 559, 610, 660, 711, 762, 889, 1016, 1143, 1270, 1397, 1524, 1651, 1778, 2032µm
- 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 14, 16, 18, 20, 22, 24, 26, 28, 30, 35, 40, 45, 50, 55, 60, 65, 70, 80mil
Measuring Procedure:
- Select appropriate comb according to approximate known thickness.
- Hold comb perpendicular to surface coating to be measured.
- Press into coating until the comb stands square on substrate.
- Wet film thickness is between the highest step which is coated and the next (higher) step which remains uncoated.
- Wipe & clean the combs after use.
Comes With
How it Work?
Width of weld seam
Bevel angle of weldment
Undercut depth of weld seam
Gap size
Features:
Measures size range from 0 to 20mm
Made by stainless steel with lasers etched markings
A special measuring tool to measure the angle of weldments crevasse and the weld width, height, weld.
Widely applied for measuring welding parts such as boilers, pressure vessels,etc.
Portable,easy to use.
Specification:
Material:Stainless Steel
Product thickness: 2mm
Part No | Range | Resolution | Accuracy | Size of Jaw |
BMDC-1001 | 0-150mm | 0.01mm | /-0.03mm | 40*36 |
BMDC-1002 | 0-200mm | 0.01mm | /-0.04mm | 40*36 |
BMDC-1003 | 0-300mm | 0.01mm | /-0.05mm | 40*36 |
Used for:
- Angle of preparation
- Excess weld metal
- Depth of undercut
- Depth of pitting
- Weld throat size
Gauge set comes with a precision ground calibration block as shown above, each block has been surface ground to 0.0005 tolerance
for exceptional accuracy.
--Used to check that any undercut is no greater than 0.010" (0.25mm) deep when the weld is transverse to the primary stress in the part that is undercut. Includes a precision ground calibration block with 0.0005" tolerance
Wire Metal Sheet Thickness Gauge Preparation Tools
Description:
This stainless steel welding gage is thicken design, not easy to deform and durable .and useful for checking metal sheet wire size before welding or working. Sizes and numerals are etched into the surface for clarity and easier reading, and stable wear-resisting. Compact and light in weight, easy to carry.
Features:
It is most useful for checking metal sheet wire size before welding or working.
Made of stainless steel, and through multiple processes, thicken design, not easy to deform and durable
Sizes and numerals are etched into the surface for clarity and easier reading, and stable wear-resisting.
Permits quick and accurate measuring of the most popular welding thickness.
Compact and light in weight, easy to carry.
Specifications:
Material:stainless steel
Weight:15g
Size: 16x6x0.5mm
Measuring range(imperial):
24GA (.0239)
22GA (.0299)
20GA (.0359)
18GA (.0478)
16GA (.0598)
14GA (.0747)
1/8" (.0125)
10GA(.1345)
3/16" (.1875)
1/4" (.250)
5/16" (.3125)
(.024")
(.030")
(.035")
Package Included:
1 x Metal Sheet Thickness Gauge
Function:
Check Fillet Leg & Throat Size
2 1/8 Inches to 3 Inches Large size, 1/8 Inch Increments
The 8 leaves joint together with screw, can be take apart easily and measure different size
Features:
Made of high quality stainless steel.
Highly ground surface
Well lapped
Precision manufactured by machine.
Specification:
The gauge is designed for measuring gap with 0.01mm resolution, Especially for steam turbine gap. It is the same function as the mechnical one. but digital one is much easy to use and read the data. It is also refered to as digital feeler gauge in Power station.
Features:
--- To Measure the gap or groove. The same function as taper gauge without digital display.
---- Large LCD Display
---- suitable to different standard
---- For Power station use
---- High ground surface
---- Stainless steel
---- Packed with wooden box.
Manufacturer: ROK International Industry Co., Limited.
Specifcation:
Range: 0.2-10mm
10-20mm
20-30mm
30-40mm
Note: the real value must devide 10 . for example, The display show data 7. the real value is 0.7mm
Order No | Range | Accuracy | Resolution |
TAWG-70801 | 0.2-10mm | /-0.02mm | 0.01mm |
TAWG-70802 | 10-20mm | /-0.02mm | 0.01mm |
TAWG-70803 | 20-30mm | /-0.02mm | 0.01mm |
TAWG-70804 | 30-40mm | /-0.02mm | 0.01mm |
Features:
-Accuracy
-Extra longer upper jaw than standard caliper
-Large Clear LCD display
-Stainless Steel
-Zero at any position
Specification
Art No | Range(mm) | Accuracy | B | Ouside Measuring Jaw | Remark |
ELDC-20421A | 0-150 | 0.03mm | 45mm | 40 | |
ELDC-20422A | 0-200 | 0.04mm | 50mm | 50 | |
ELDC-20423A | 0-300 | 0.05mm | 55mm | 60 |
|
Wet Film Thickness Wheel Roller Type
0-100um A
0-200um B
Roller type wet film thickness gauge is used to measure the thickness of paint, varnish and other coating wet film.The thickness gauge can not only be measured on the flat substrate, but also on the curved substrate.
Roller coating thickness gauge measurement method
Since it is not possible to exclude pigment particles remaining between the instrument and the substrate, all mechanical test methods contain systematic errors that indicate that the paint film thickness is at least one average diameter of the pigment particles lower than the actual wet film thickness.
The roller thickness gauge is used to accurately measure the thickness of wet film coating (paint ink, etc.).When measuring, the measuring wheel with eccentric rim is rolling on the paint film.
The eccentric rim is marked with scale, the gap gradually increases, the wheel is allowed to roll the paint during the test, the contact point of the rim indicates the thickness of the paint film.
Roller Type Wheel Gauge Wet Film Thickness Gauge Coating Wet Film Gauge
There are four standard measurement ranges: 0-100 microns;0-200 microns;0-500 microns;0-1000 microns
What is it used for?
Why Roktools?
Features:
*100% brand new and high quality
*Made of high quality material, durable and practical to use
*Large LCD for easy reading
*Lightweight and portable
*Novel design, Large display window
*For measuring the thickness of Jewel Gem Gemstone
*Functions / manual ON/OFF or auto power off, zero setting at any position ,Metric /Inch system conversion at any position
Specifications:
*Color: Black (As Pictures Show)
*Material: ABS metal
*Size: 142 * 30mm (Approx.)
*Measuring range: 0-25 mm
*Resolution: 0.01mm/0.0005
*Battery: 1.5V LR44 (Not included)
*Working temperature: 0-40ºC
*Storage temperature: -20degree Celsius~70degree Celsius
*Relative Humidity: 0% - 80%
Features:
Metal casing zinc alloy, Protect the chip and display
DIN ANSI ISO GB JIS Standard, Designed for calibration (we do not provide third party calibration service)
Less shaking error
With Paralleled jaw
Smooth slide for easier movement of display
Precision ground measuring face for accurate measurement.
Specification:
Order No | Range | Resolution | Accuracy | Remarks |
DC-154A | 0~150mm/6″ | 0.01mm/0.0005″ | 0.02mm | Industrial use |
DC-254A | 0~200mm/8″ | 0.01mm/0.0005″ | 0.02mm | Industrial use |
DC-354A | 0~300mm/12″ | 0.01mm/0.0005″ | 0.03mm | Industrial use |